Home > Driver Mouse > Driver Mouse Serial Linux

Driver Mouse Serial Linux

Installing the package linuxconsoletools from the testing repository and executing inputattach --mouseman /dev/ttyS0 should give us a working mouse for the X server. The loop is fairly standard for event waiting in Linux. For a setup with an USB mouse and keyboard you'd use: USB support --->
Support for USB
Preliminary USB device filesystem
UHCI (Intel PIIX4, VIA, ...) support
OHCI (Compaq, iMacs, OPTi, The program is interactive and will print at the end a message like: Your mouse seems to be a 'mman' one on "/dev/ttyS0" (24 matches) The man page gpm-types contain a navigate here

The newer lock file system doesn't fall into this trap so it's now OK to use such links. 10.7 Which Connector on the Back of my PC is ttyS1, etc? You can get it from ftp.kernel.org. You will also see support for extended options for more advance 16550 types devices. Linux normally parcels out devices by major number, each of which has 256 minor devices associated with it; however, for things like mice this is extremely wasteful, since these drivers only https://help.ubuntu.com/community/SerialMouseHowto

Manual editing of the xorg.conf file (without leaving graphical mode) How to set up a serial mouse using only the keyboard and without working in a text-only console. If no devices become available, reconfigure udev or disable AutoAddDevices. The "Auto" platform specifies that protocol auto-detection should be attempted.

The most important device files are listed in the tables below. fd0 First Floppy Drive fd1 Second Floppy Drive sda First hard disk sdb Second hard disk sda1 First An inputattach instance will be started for each element. If you decided to try out the new serial drivers you will see: Serial port support
If you enable it for the ix86 platform you will see: Serial port However, most mice use a common protocol called the bus mouse protocol.

Each read from a bus mouse interface device returns a block of data.

For two 9-pin ones the top one might be ttyS0. Restart X by logging out and back in, or typing sudo/etc/init.d/gdmrestart. Checksumming Files to Find Bit-Rot What's an inode? http://lxr.free-electrons.com/source/drivers/input/mouse/sermouse.c This is because we do not want to request the interrupt multiple times.

Default: off. Which com port it actually is will depend on jumper or PnP settings (sometimes shown in a BIOS setup menu). The mouse interface is for backwards compatibility. The idea is that mouse movements outside of the allowed range should generate additional mouse events until the entire movement is accounted for (in chunks of +/-127 apiece).

If the serial ports have been configured correctly per setserial, then you may send some bytes out a port and try to detect which connector (if any) they are coming out https://wiki.archlinux.org/index.php/Serial_input_device_to_kernel_input All the methods described below are now deprecated and will probably not work with HAL detection used since Ubuntu 9.04 Jaunty. If you want to stop inputattach when stopping the local service, create an executable file /etc/local.d/sermouse.stop with content #!/bin/sh killall inputattach Alternatively you can create a script in /etc/init.d to define If our driver were capable of sharing an interrupt line, we would specify SA_SHIRQ instead of zero as the third argument to request_irq.

Press right arrow to get into the next "menu". check over here Default: 200. Until then, you might want to have a look at other device drivers to get a feel for how this all works.

Alan Cox is a well-known Linux hacker. Then by clicking on the mouse, or otherwise sending characters with the device, see if they get displayed.

Now the output of cat /proc/bus/input/devices should contain a section like: I: Bus=0013 Vendor=0004 Product=0001 Version=0100 N: Name="Logitech M+ Mouse" P: Phys=ttyS0/serio0/input0 S: Sysfs=/devices/platform/serial8250/tty/ttyS0/serio8/input/input9 U: Uniq= H: Handlers=event2 mouse0 B: PROP=0 Go from the top menu into: Character devices --->
Now you will see something like: Virtual terminal
Support for console on virtual terminal
You need to enable these if you want When the xserver restarts, your mouse should work normally. his comment is here See the help for this utility about what the command line will be for your mouse - there are quite a couple different types of them.

A voltmeter connected to the DTR pin (see Serial-HOWTO for Pinout) will display a positive voltage as soon as you give the copy command. Getting information about the mouse If the protocol for the serial mouse is unkown, the command mouse-test /dev/ttyS0 from the package gpm can be used to get the necessary information. with a focused XTERM in the middle of your screen.

He can be reached at [email protected]

Comments are closed.

The respective configuration files are /etc/gpm.conf and /etc/X11/xorg.conf. For a most usual setup with a PS/2 mouse and a AT keyboard you need to select: Input device support --->
Input device support
i8042 aux+kbd controller
AT and PS/2 keyboards
The linuxconsole package is in community: # pacman -S linuxconsole Configuration and usage Once you have installed package, you can view the inputattach help, to see the large list of serial old
mkdir input
cd input
mknod js0 c 13 0
mknod js1 c 13 1
mknod js2 c 13 2
mknod js3 c 13 3
mknod mouse0 c 13 32
mknod

Here, there is only one kind of event: the mouse_event flag indicates whether there was a change in the mouse status. Some motherboards come with a serial port with no cable or external serial DB connector. If you select the new serial drivers you can't select the old drivers. weblink Option Emulate3Buttons boolean Enable/disable the emulation of the third (middle) mouse button for mice which only have two physical buttons.

We hope with the serial layer being written that in the future you will not need this. The misc device itself is simply acting as a redirector for requests.

Next, in order to be able to use and test our driver we need to add some module wrapper For example, ttyS2 would correspond to cua2. If you are installing on a PC with a mouse attached to a serial port (rather than the mouse port), here's what you need to do...

To access the CVS you can use the following commands (use an empty password): cvs -d :pserver:[email protected]:/cvsroot/linuxconsole login
cvs -z3 -d :pserver:[email protected]:/cvsroot/linuxconsole checkout ruby
Once you have downloaded the CVS, you There is nothing stopping us providing an ioctl function for this mouse.